Leveling Machine-manufacture,factory,supplier from China

a. Form: Roller type active leveling machineb. Functional and structural features: leveling steel belt. It consists of pinch rollers and leveling rollers. The pinch rollers can be adjusted individually. The upper leveling roller adopts an integral structure and has two adjustment points at the front and rear, which can form a certain tilt angle to improve the leveling quality. The upper pinch feeding and leveling rollers are raised and lowered using 8.8-grade high-quality ball screws.

1、Hydraulic decoiler with a load capacity of 10 tons2、Roller type active leveling machine，Both the front and rear of the leveling machine are equipped with feed bridge devices. An electronic detection device is installed between the leveling machine and the feeder, which sends a feedback signal to the control system.

main component1. Uncoiler, coil width: 850mm, coil inner diameter: 530mm, maximum coil outer diameter: 1500mm, hydraulic station 3KW set, load-bearing 8 tons2. Leveling and cutting machine, code feeding forward rotation mechanism (forward and reverse screw), 13-roller leveling, 45 on the leveling shaft, 7.5KW motor, hydraulic cutting, pallet punching3. A-section high-speed platform, 2-section high-speed platform, front and back screw width adjustment, feeding speed controlled by frequency conversion4.

primary component1. Uncoiler, hydraulic core, distribution container (frequency conversion manage sluggish upward push and sluggish stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. A leveling computing device with eleven leveling rollers (3 top and four lower), with a energy of 5.5KW.3.

1. Uncoiler, hydraulic core expansion, distribution box (frequency conversion control slow rise and slow stop), hydraulic 3KW set, load-bearing 8 tons2. Leveling and cutting machine, 13-roller leveling, hydraulic system 11KW, 2 sets of electric valves, 7.5KW motor, hydraulic cutting, pallet punching3. A-section high-speed platform, 2 high-speed platforms, forward and reverse screw width adjustment, frequency conversion control4. Punch machine, 3 motors, distribution box, mold pneumatic conversion single and double row, oil cylinder heavy engineering oil cylinder5.

main component1. Uncoiler, load-bearing 4 tons, distribution box (frequency conversion control slow stop)2. Leveling machine, 1 roller leveling (3 upper and 4 lower), power 4.0KW3. All-in-one punching and cutting machine, code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, punching die manual pin conversion single and double row, hydraulic cutting, typing (trademark) (optional)4. High-speed platform - high-speed platform, forward and reverse wire width adjustment, frequency conversion control5.

main component1. Uncoiler, hydraulic core, distribution box (frequency conversion control slow rise and slow stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. A leveling machine - 11 roller leveling (3 upper and 4 lower), power 5.5KW,3. Integrated punching and shearing machine - code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, hydraulic cutting, manual pin conversion of single and double rows of punching die, typing (trademark), pallet punching4.

main component1、 open rolling machine ， manual core rise, electric material discharge, load-bearing 4 tons, distribution box (frequency conversion control slow slow stop)2、 leveling machine ， 11 roller leveling (up 3 down 4), power 4.0KW3、 punching and cutting machine ， feed code forward mechanism (positive and reverse screw), hydraulic punching, hydraulic cutting, punching die manual pin transform single and double row, typing (trademark) (optional)4、 high-speed platform ， 1 high-speed platform, frequency conversion control, forward and reverse wire rod width adjustment5 、roller press forming

Technical Parameters:1. Material: galvanized steel strip, etc.2. Material thickness: 0.5～2.0mm3. Material width 100~1250mm4. Production efficiency: 0～16m/min (adjustable with variable frequency)5. Roller pressing method: pneumatic pressing6. Leveling adjustment method: worm gear adjustment7. Power mode: servo motor + precision planetary reducer8. Leveling shaft composition: upper 4 and lower 5 (leveling shaft) + upper 2 and lower 2 (pinch shaft)9. Change model: manual adjustment10. Operating air pressure: 0.6MPa11. Power 7.5kw12.

main component1. Uncoiler, hydraulic core expansion, distribution box (frequency conversion control slow rise and slow stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. Leveling machine, 11 roller leveling (3 upper and 4 lower), power 5.5KW,3. Integrated punching and shearing machine, code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, hydraulic cutting, manual pin conversion of single and double rows of punching die, typing (trademark), pallet punching4.

main component1、Open winding machine，load-bearing ten tons of electric hydraulic open rolling machine2、Leveling and cutting machine，13 roller leveling, hydraulic cutting, tray punching Section A high-speed 3、platform， high-speed platform 2 branches, frequency conversion control 4、Punch machine，hydraulic system (7.5kw2 sets), mold pneumatic conversion single and double row, oil cylinder heavy engineering cylinder, typing (trademark Section 5、 high-speed platform，high-speed platform 2 (1 electric 0.75kw, 1 passive), the width of the positive and reverse wire rod is adjusted6、 Roller fo

1. Uncoiler, manual core starting, load bearing 4 tons, distribution box (frequency conversion control slow stop)2. Leveling machine, 11 roller leveling (3 upper and 4 lower), power 4.0KW3. Integrated punching and cutting machine - code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, punching die manual pin conversion single and double row, hydraulic cutting, typing (trademark) (optional)4. High-speed platform - high-speed platform, forward and reverse wire width adjustment, frequency conversion control5.

main component1、Open winding machine，load-bearing ten tons of electric hydraulic open rolling machine2、Leveling and cutting machine，13 roller leveling, hydraulic cutting, tray punching Section A high-speed 3、platform， high-speed platform 2 branches, frequency conversion control4、Punch machine，hydraulic system (7.5kw2 sets), mold pneumatic conversion single and double row, oil cylinder heavy engineering cylinder, typing (trademark Section 5、 high-speed platform，high-speed platform 2 (1 electric 0.75kw, 1 passive), the width of the positive and reverse wire rod is adjusted6、 Roller for

main component1、Open winding machine，load-bearing ten tons of electric hydraulic open rolling machine2、Leveling and cutting machine，13 roller leveling, hydraulic cutting, tray punching Section A high-speed 3、platform， high-speed platform 2 branches, frequency conversion control4、Punch machine，hydraulic system (7.5kw2 sets), mold pneumatic conversion single and double row, oil cylinder heavy engineering cylinder, typing (trademark Section 5、 high-speed platform，high-speed platform 2 (1 electric 0.75kw, 1 passive), the width of the positive and reverse wire rod is adjusted6、 Roller for

main component1、Open winding machine，load-bearing ten tons of electric hydraulic open rolling machine2、Leveling and cutting machine，13 roller leveling, hydraulic cutting, tray punching Section A high-speed 3、platform， high-speed platform 2 branches, frequency conversion control4、Punch machine，hydraulic system (7.5kw2 sets), mold pneumatic conversion single and double row, oil cylinder heavy engineering cylinder, typing (trademark Section 5、 high-speed platform，high-speed platform 2 (1 electric 0.75kw, 1 passive), the width of the positive and reverse wire rod is adjusted6、 Roller for

NO.ElementQuantity1Uncoiler12Leveling and cutting machine13Conveyor platform44Punching machine15Roll forming machine16Unloading rack1Process flowUncoiler → Leveling and cutting machine → Conveying platform → Punching machine → Conveying platform → Roll forming machine → Unloading platform

main component1 、feeding rack ， hydraulic feeding rack2 、leveling ， unpowered 5 roller leveling (top 2 bottom 3)3 、roller forming ， spindle surface plating hard chromium, forming roll 16 rows, the main machine is divided into 2 sections, forming plane straight 1 set, roll material: GCR 154、 tracking cut ， hydraulic cut, servo tracking, hydraulic system a set of 4KWTechnical Parametersorder numberprojectunitnumerical value1Material widthMmInplate width 600mm2Material thicknessMm0.5～1.2mm3material type galvanized steel strip   4Equipment running speedm/min1-15 m/min5powerKw&n

main component1 open rolling machine —— manual core rise, active feeding, load-bearing 2 tons, distribution box (frequency conversion control slow slow stop)2 leveling machine —— 5 roller leveling (top 2 bottom 3)3 tracking punch —— feed code forward mechanism (positive and reverse wire bar), hydraulic punch, servo tracking, Hydraulic system with one set of 5.5+5.5KW4 roller forming —— spindle φ 40mm, surface coated with hard chromium, forming roll 20 rows, the main machine is divided into 2 sections, side reinforcement, extended feed guide position, 1 set of plane calibration after forming, r

The gear is outfitted with a decoiler with a load potential of eight tons, hydraulic core expansion, and electric powered feeding, which is extra handy to operate. Below is the leveling and cutting. Our leveling computing device will straighten the plate of the steel coil and then reduce it into the required length.

1、 Open coil ， hydraulic core rise, distribution box (frequency conversion control slow up slow stop), electric discharge, a set of hydraulic 3KW, bearing 8 tons2 、leveling and cutting machine， 13 roller leveling, hydraulic system 11KW 2 group electric valve, 7.5KW motor, hydraulic cutting, tray punching3、 A section high speed platform ， high speed platform 2 branches, the width of the positive and reverse wire rod adjustment, frequency conversion control4、 punching machine ， motor 3 sets, distribution box, mold pneumatic conversion single and double row, oil cylinder heavy engi

Main Component1 open rolling machine —— hydraulic core rise, electric feed, load bearing 5 tons, distribution box (frequency conversion control slow up slow stop), hydraulic system a set of 3.0KW2 leveling and cutting machine —— hydraulic system 11KW, hydraulic cutting, 11 roller leveling, 5.5KW motor3 high-speed platform —— 1 high-speed platform, frequency conversion control, positive and reverse wire rod width adjustment, frequency conversion control4 roller forming part —— spindle φ 60mm, surface hard chromium, forming roller 6 rows, reinforcing reinforcement, hydraulic punching, roll mater

Process flow and characteristics:Winding → Leveling → Disk cutting strip → Waste edge winding → Tension → Coiling → Unloading1、This machine and equipment is a complete set of process machinery and equipment, which can produce a variety of qualified hot steel coils of different specifications, cold-dip galvanized steel coils, Q235, color steel coils, color-coated coils, aluminum coils, stainless steel coils, etc. 2、This machine adopts more automatic hydraulic controls and pneumatic controls, which reduces the weight of the equipment, simplifies the structure of the equipment, reduces labor

Main Component1、 open coil machine ， 300 type open coil, passive feeding, load-bearing 1.5 tons, with brake function2、 leveling, punching, cut off —— hydraulic system 111 KW, hydraulic cut off,3、 High-speed platform ， frequency conversion control, 1 high-speed platform, forward and reverse wire rod width adjustment4、 roller forming part ， spindle φ 60mm, surface plating hard chromium, forming roller 6 rows, roller material: GCr 15, lengthened feed guide position, 1 set of plane calibration after forming5 、unloading rack ， passive unloading rack: 1 branchTechnical Parametersserial numberproject

main component1、Open rolling machine ，hydraulic core, bearing 5 tons, distribution box (frequency conversion control slow up slow stop), hydraulic 3KW set 2 ， 13 roller leveling, hydraulic system 111 KW 2 group electric valves, 7.5KW motor , Hydraulic cutting, tray punching (optional) 3, section A high speed platform ， 2 high speed platform, width adjustment of positive and reverse wire rod, frequency conversion control, 4, punching machine，mold pneumatic transformation single and double row, oil cylinder heavy engineering cylinder, typing (trademark) (optional) 5, section